CMSC110 (Introduction to Computing)

Fall 2014

Assignment#6

Due by 10:00p on Tuesday, December 9, 2014
[THERE WILL BE NO CREDIT FOR SUBMISSIONS TIME STAMPED AFTER 10:00p]

First, read Chapter 6 from GXK.

This assignment has TWO PARTS.

Task: Design an underwater creature. The creature should be designed so that it can be instantiated as an object. Make sure you name the class as <YourFirstInitialLastName>Thingy. For example Deepak Kumar's creature will be defined in a class called DKumarThingy. Barack Obama's creature will be BObamaThingy. You should be able to create instances of the creature with varying sizes. In addition to the constructor, make sure that the class includes a method called display() so that one could incorporate your creature in a sketch as follows:

DKumarThingy DKFish;		// An instance of DKumarThingy will be called DKFish
float SIZE;				// The SIZE of the instance that will be created


void setup() {
	size(_, _);
  smooth();
  SIZE = ...;
  DKFish = new DKumarThingy(SIZE);	// Create an instance with size, SIZE
...

} // end of setup


void draw() {
	

  // display the creature
  DKFish.display();



} // end of draw


class DKumarThingy {	// Definition of the creature DKumarThingy
 DKumarThingy(float _size) {
	...
 }


 void display(...) {

	...
 } // display()


   ...
}// end of class DKumarThingy

The focus should be on the use of classes to define the object factory. You will need to write the constructor, and the operations as described above.

Make sure that your creature is not too small, nor too large, as it will have to live in an aquarium with 50+ other creatures!

Part 2: Next, you will extend the creature's definition. Add a new behavior move() to your creature's class. Depending upon the creature you designed in Part 1, define appropriate move() behavior. Some creatures will swim like a fish, or a submarine, some will wiggle about, some might just stay in one place and rotate, bubble, etc. If the creature is moving about, make sure that it either stays within the bounds of the sketch or emerges at the other end. Strategies for implementing these will be discussed in class. Here is a revised skeletal sketch that will create one instance of the creature and have it show its behavior.

DKumarThingy DKFish;		// An instance of DKumarThingy will be called DKFish
float SIZE;				// The SIZE of the instance that will be created


void setup() {
	size(_, _);
  smooth();
  SIZE = ...;
  DKFish = new DKumarThingy(SIZE);	// Create an instance with size, SIZE
...

} // end of setup


void draw() {
	

  // the creature moves
DKFish.move();
// display the creature DKFish.display(); } // end of draw class DKumarThingy { // Definition of the creature DKumarThingy
 DKumarThingy(float _size) {
	...
 }


 void display(...) {

	...
 } // display()

void move() {
...
} // move() ... }// end of class DKumarThingy

 

In your overall sketch pay special attention to the aesthetic aspects of your design. Write your own aquarium sketch where you can display several of your creatures of varying sizes. Make it 800x600 pixels, though your sketch should be written so the sketch size can vary without affecting the creature, or its movements.

What to Hand in: Hand in the entire sketch folder in your Dropbox folder. In addition to the sketch/programs also include; (1) a gif/jpg/png image of your finished sketch. (2) A formatted write-up with Page#1 showing your sketch, followed by a title, your name, a short 1-2 line description (as discussed in class) on page#1, and a short 1-2 paragraph more detailed description of the sketch and your personal experiences working on this sketch.

Back to CMSC110 Course Web Page